|
Home Made Press!
started by Triple650Indy
|
|
|
|
November 21st 2006 at 1:45 PM
|
|
| |
|
|
| |
Check this out, after talkin to my dealer, in which he told me he didn't have a press that could press the drivers off the drive shaft I decided to try my hand. This is what I came up with.
Just throwing this out there.
Cause I don't give a rats about who took second or 12th for that matter your just the next loser in a long line of many losers.
|
|
 |
|
|
|
|
|
|
| |
Site Supporter
Group: Site Supporters
|
|
| |
|
|
|
|
|
|
|
November 21st 2006 at 1:51 PM
|
|
| |
|
|
| |
i love it when people invent stuff so they can do it them selves. that rocks man
|
|
|
|
|
|
|
November 21st 2006 at 2:12 PM
|
|
| |
|
TheKuskokid
Frustrated chemist
|
1056 Posts 
Group: Members
Member Since: September 30th 2005
Location: Bethel, AK, USA
Current Sled: '07 BearCat
Miles Last Season: 1575
Miles This Season: 2000
|
|
|
|
| |
They go on much easier if you grease the shaft too.
You can piddle with the puppies, or run with the wolves...
Better living through chemistry.
|
|
|
|
|
|
|
November 21st 2006 at 3:39 PM
|
|
| |
|
Blackcat
Senior Member
|
3698 Posts 
Group: Members
Member Since: October 24th 2004
Location: Wahpeton, ND, USA
Current Sled: 94 AC ZR580
Miles Last Season: 130
Miles This Season: 318
|
|
|
|
| |
Looks good 650! Now thats enginuety at work.
'94 ZR580
Remember, the things we say and write not only effect those it was intended for, but can also effect the greater population...whether good or bad.
School Location: Wahpeton, ND (NDSCS)
Home Location: Berthold, ND
My Site
06-07 Sleddin' Season Stats
|
|
|
|
|
|
|
November 21st 2006 at 3:49 PM
|
|
| |
gogophers
Junior Member
|
300 Posts 
Group: Members
Member Since: February 28th 2005
Location: Crookston, Minnesota, USA
|
|
|
|
| |
nice. how long did it take you to come up with that?
|
|
|
|
|
|
|
November 21st 2006 at 4:23 PM
|
|
| |
|
|
| |
The design took me all of 5 sec the actual construction took 30 minutes. And now I've got an issue. I made the studs too short to reverse and use to press the new ones on. So I may just have my dad take it down to his work and see if their press is large enough.
Cause I don't give a rats about who took second or 12th for that matter your just the next loser in a long line of many losers.
|
|
|
|
|
|
|
November 21st 2006 at 4:51 PM
|
|
| |
|
greasemonkey
Northwoods Powdercoating
|
904 Posts 
Group: Members
Member Since: November 18th 2005
Location: proctor, mn, USA
Current Sled: 07 Rage GT
Miles Last Season: 2400
Miles This Season: 3488
|
|
|
|
| |
Nice idea, the only concern I have is mild steel and mild threaded rods + hyd. jack = look out for flying steel !!! ( been there, done that )
|
|
|
|
|
|
|
November 22nd 2006 at 12:30 AM
|
|
| |
|
|
| |
Worked good, thanks for you concern though Greasemonkey. Someone cares. 
Cause I don't give a rats about who took second or 12th for that matter your just the next loser in a long line of many losers.
|