|
Need Help
- 96 ZRT 600
started by edman2007
|
|
|
|
February 17th 2008 at 4:20 PM
|
|
| |
edman2007
Comanche Owner
|
68 Posts 
Group: Members
Member Since: March 1st 2007
Location: Lanesboro, MN, USA
Current Sled: '96 ZRT 600
|
|
|
|
| |
I have a ZRT and was wondering what the spark plug wiring is (the order). It doesnt idle at all unless I give it a little gas then it will. It reves up to 5k rpms and the clutch engages. It then hesitates and stays at 5.5k for a few seconds until it hits 6-6.5k then it takes off and only hits 7k rpms max. I need help for possible problems.
If practice makes perfect and nobody is perfect, why practice?
Sleds:
1979 Yamaha Enticer 300 twin (mine)
1983 Polaris Cutlass 440 (little bro's)
1981 Polaris Indy Centurion (mine) For Sale!
1996 Arctic Cat ZRT 600 (mine)
1997 Arcitc Cat ZRT 600 (mine, crashed parts sled) Parting Out Everything!
|
|
 |
|
|
|
|
|
|
| |
Site Supporter
Group: Site Supporters
|
|
| |
|
|
|
|
|
|
|
February 17th 2008 at 9:47 PM
[ Modified February 17th 2008 at 9:47 PM
]
|
|
| |
stormrider62033
wally
|
3770 Posts 
Group: Members
Member Since: December 25th 2004
Location: Gillespie, IL, USA
Current Sled: 99xcr 800
Miles Last Season: 500
Miles This Season: 500
|
|
|
|
| |
take the carbs off and clean them ,another important thing to do on these is to run isoheet ,these are real touchy to water in the fuel ,,start with that first
mid Il alway's waiting for snow,moving north(way north)99xcr 800 97SPX ULTRA 96 zrt 600&800,92 doo plusX 92 v max 4
|
|
|
|
|
|
|
February 18th 2008 at 7:54 PM
|
|
| |
edman2007
Comanche Owner
|
68 Posts
Group: Members
Member Since: March 1st 2007
Location: Lanesboro, MN, USA
Current Sled: '96 ZRT 600
|
|
|
|
| |
Quote originally posted by stormrider62033
take the carbs off and clean them ,another important thing to do on these is to run isoheet ,these are real touchy to water in the fuel ,,start with that first
Ok, got them all cleaned up again. Now I need the spark plug wiring order
If practice makes perfect and nobody is perfect, why practice?
Sleds:
1979 Yamaha Enticer 300 twin (mine)
1983 Polaris Cutlass 440 (little bro's)
1981 Polaris Indy Centurion (mine) For Sale!
1996 Arctic Cat ZRT 600 (mine)
1997 Arcitc Cat ZRT 600 (mine, crashed parts sled) Parting Out Everything!
|
|
|
|
|
|
|
February 18th 2008 at 8:08 PM
[ Modified February 18th 2008 at 8:10 PM
]
|
|
| |
|
Mustangnut6788
Junior Member
|
391 Posts 
Group: Members
Member Since: January 29th 2006
Location: Wickliffe, OH, USA
|
|
|
|
| |
I don't think it really matters. The length and routing of the wires should show you where they go. The diagram shows the coil with one plug wire goes to #3. The coil with two plug wires coming out: wire on CDI side goes to #1 and the jumper wire to the other coil side is #2.
Sounds like you have choke issues. Make sure you have them adjusted right.
Hope that helps ya bud!
My Toys:
2001 Arctic Cat ZRT 600
1999 Arctic Cat Thundercat 1000
1993 Mustang Coupe
1988 Mustang GT 5.0L
2000 F-150
|
|
|
|
|
|
|
February 18th 2008 at 10:04 PM
|
|
| |
edman2007
Comanche Owner
|
68 Posts
Group: Members
Member Since: March 1st 2007
Location: Lanesboro, MN, USA
Current Sled: '96 ZRT 600
|
|
|
|
| |
After cleaning the carbs once(before my last post), i ran it for a while and one cylender cut out. Took them apart again and i found more junk in there than before. I'm cleaning them again and going to run it and see what happens. This sled had been sitting for a while when I got it so I expected this. Any tips on the adjustments for the carbs? It has everything stock but for the silencer (its 3 straight cylenders onto the pipes).
If practice makes perfect and nobody is perfect, why practice?
Sleds:
1979 Yamaha Enticer 300 twin (mine)
1983 Polaris Cutlass 440 (little bro's)
1981 Polaris Indy Centurion (mine) For Sale!
1996 Arctic Cat ZRT 600 (mine)
1997 Arcitc Cat ZRT 600 (mine, crashed parts sled) Parting Out Everything!
|
|
|
|
|
|
|
February 19th 2008 at 8:52 AM
|
|
| |
|
arcticcatmatt
Spleen Splitter
arcticcatmatt is a little wasted.
Updated Yesterday at 9:55 PM
|
11784 Posts 
Group: Moderators
Member Since: November 25th 2001
Location: Berkshire, NY, USA
Current Sled: 96/97 ZRT 600
Miles Last Season: 100
Miles This Season: 462
|
|
|
|
| |
^ There are 1-2 how twos on her for cleaning your mikuni rounds. Check the article section and the how-to section.
Make SURE your chokes are adjusted right. You have to have 1/16 ish of play in the lever at LEAST. If you don't, they are not seating and thats why it will not idle.
Check that stuff and report back 
|
|
|
|
|
|
|
February 19th 2008 at 10:38 AM
|
|
| |
|
|
arcticcatmatt
Spleen Splitter
arcticcatmatt is a little wasted.
Updated Yesterday at 9:55 PM
|
11784 Posts
Group: Moderators
Member Since: November 25th 2001
Location: Berkshire, NY, USA
Current Sled: 96/97 ZRT 600
Miles Last Season: 100
Miles This Season: 462
|
|
|