|
 |
|
 |
 |
|
2002 Edge x 800 moded but will die out after giving it gas
started by Craig_Polaris
|
|
|
|
November 11th 2008 at 12:29 AM
|
|
| |
|
Craig_Polaris
Junior Member
|
147 Posts 
Group: Members
Member Since: November 11th 2008
Location: Derry, New Hampshire, USA
Current Sled: 2002 Edge X 800
|
|
|
|
| |
So i got a 02 edge x 800 it has slp air box, vforce 3 reeds, slp pipe and silencer and a new 1.25 track on it. But i just fired it up this year and picked the back end up and granted it was about 45 degrees out but after it was kinda warm and i hit the gas to about 5500 rpm and let off the gas the sled would go down to about 300rpm then die out. Any ideas?
2002 Edge x 800; Recently swallowed a valve so, New wiseco pistons, rings, pins, circlips, renikisil cylinders, and updated lower end bearings.
- Slp single Pipe and Can
- Vforce3 Reeds
- Slp air horn and gutted box
- 140/310 Slp primary spring
|
|
 |
|
|
|
|
|
| |
Site Supporter
Group: Site Supporters
|
|
| |
|
|
|
|
|
|
November 11th 2008 at 5:40 AM
|
|
| |
|
santo5
Complete khaos
|
1215 Posts 
Group: Members
Member Since: October 11th 2007
Location: shelby twp, michigan
Current Sled: 01 xcsp 600
2008-2009 Miles: 00000000
|
|
|
|
| |
did you ever have the crank updates? I'm shere many people will cherp in on the 02 800s.
|
|
|
|
|
|
November 11th 2008 at 5:31 PM
|
|
| |
|
steve13
Starting Member
|
43 Posts
Group: Members
Member Since: December 28th 2006
Location: Quebec, Quebec, Canada
Current Sled: XC 800 2002, XCR 800 2003
|
|
|
|
| |
seem like a fuel problem. last year I have the same problem on my xc 800 2002(start it and die out) and when I take of my pipe, lot of injection oil came off. a oil injection valve on the base was the problem, the base was full of oil and the vacuum rubber hose from the base to the fuel pump was full of oil too.
I take off oil from the base and from the hose, and everything turn out to be OK.
maybe it's not the same problem, but seem like fuel. (fuel valve, fuel line, carbs) check it out.
Steve
XCR 800 2003
XC 800 2002
Ultra 1998 LRM pipes
Ultra SP 1996
project to come: XCR 800 motor in Ultra 96 body
|
|
|
|
|
|
November 11th 2008 at 7:31 PM
|
|
| |
|
|
Craig_Polaris
Junior Member
|
147 Posts
Group: Members
Member Since: November 11th 2008
Location: Derry, New Hampshire, USA
Current Sled: 2002 Edge X 800
|
|
|
|
| |
Quote originally posted by steve13
seem like a fuel problem. last year I have the same problem on my xc 800 2002(start it and die out) and when I take of my pipe, lot of injection oil came off. a oil injection valve on the base was the problem, the base was full of oil and the vacuum rubber hose from the base to the fuel pump was full of oil too.
I take off oil from the base and from the hose, and everything turn out to be OK.
maybe it's not the same problem, but seem like fuel. (fuel valve, fuel line, carbs) check it out.
Steve
Well it will start up and run and idle just when i give it gas to about even 5000rpm then just let off the throttle it will die to nothing
2002 Edge x 800; Recently swallowed a valve so, New wiseco pistons, rings, pins, circlips, renikisil cylinders, and updated lower end bearings.
- Slp single Pipe and Can
- Vforce3 Reeds
- Slp air horn and gutted box
- 140/310 Slp primary spring
|
|
|
|
|
|
November 12th 2008 at 4:36 PM
|
|
| |
|
|
| |
did you clean the carbs before firing it up this year? good plugs? will it rev past 5,000 rpm? 5,000 rpm is hardly past clutch engagement. kinda sounds like it's loading up.
---------------------------
- 2004 pro-xr 440/800: SLP single pipe, clutched, not enough studs, wacky oil tank mounting, crazy intake i made, REV seat/tank, C&A pro skis.
- 2006 mxzx 440 race sled
- 1989 indy trail
- 2001 800xcsp: rest in pieces.
|
|
|
|
|
|
November 12th 2008 at 4:49 PM
|
|
| |
|
powersledder
PSI Powered
|
3605 Posts 
Group: Members
Member Since: September 1st 2006
Location: Houghton, MI, USA
Current Sled: 07 IQr
2008-2009 Miles: No Speedo
|
|
|
|
| |
Check the plugs, they're probably fouling out.
Polaris 800HO monoblock cylinder for sale PM me with offers
|
|
|
|
|
|
November 12th 2008 at 8:22 PM
[ Modified November 12th 2008 at 8:22 PM
]
|
|
| |
|
|
Craig_Polaris
Junior Member
|
147 Posts
Group: Members
Member Since: November 11th 2008
Location: Derry, New Hampshire, USA
Current Sled: 2002 Edge X 800
|
|
|
|
| |
nope plugs are good, not fouling them at all, i can rev it past 5000 i could rev it all the way up but as soon as i let of the gas it will die down then stall out
i'm running standard plugs in it and they are not white and not to black
2002 Edge x 800; Recently swallowed a valve so, New wiseco pistons, rings, pins, circlips, renikisil cylinders, and updated lower end bearings.
- Slp single Pipe and Can
- Vforce3 Reeds
- Slp air horn and gutted box
- 140/310 Slp primary spring
|
|
|
|
|
|
November 14th 2008 at 11:15 PM
|
|
| |
|
|
Craig_Polaris
Junior Member
|
147 Posts
Group: Members
Member Since: November 11th 2008
Location: Derry, New Hampshire, USA
Current Sled: 2002 Edge X 800
|
|
|
|
| |
well i unpluged the kill switch and it fixed the problem
2002 Edge x 800; Recently swallowed a valve so, New wiseco pistons, rings, pins, circlips, renikisil cylinders, and updated lower end bearings.
- Slp single Pipe and Can
- Vforce3 Reeds
- Slp air horn and gutted box
- 140/310 Slp primary spring
|
|
|
|
|
0 user(s) are reading this topic (0 Members and
0 Guests)
|
 |
|
