Belts started by James007
	December 28th 2008 at 1:02 PM  [ Modified December 28th 2008 at 2:37 PM by Quinlan ] Post #1
	James007 Disturbing the peace since 1991. 2090 Posts Group: Members Member Since: January 12th 2007 Location: kirkland lake, ontario, Canada Current Sled: 2009 MXZ X 600Etec 2008-2009 Miles: 1100
	Hey guys, so yeah i blew my belt yesterday. And damn the belts for my sled are cray expensive. And im very cheap at the moment especially after christmas. So im wondering how long a 40$ belt would last in my sled. And if those 120$ belts are worth it. James I noticed i wrote "BELTS" wrong. Fixed your "belts." -Quinlan 2009 MXZ X 600 ETEC www.youtube.com/sjames117 Rating: 0 Quick Edit Edit Topic

	Site Supporter Group: Site Supporters

	December 28th 2008 at 2:53 PM Post #2
	cannon3731 Starting Member 36 Posts Group: Members Member Since: January 16th 2007 Location: Michigan, USA Current Sled: 2000 Yamaha SXR 700 2008-2009 Miles: 737
	I have had the best luck with the oem belts. I tryed a cheaper belt and blew it in 70 miles just my .02 cents. Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 4:55 PM Post #3
	polarispimpman500 #1 BRP Fan... Join The Club 1145 Posts Group: Members Member Since: November 4th 2005 Location: Orillia, ON, Canada Current Sled: 2001 xc800sp 2008-2009 Miles: 120
	they might work, ive have had nothing but problems with ****ty belts. my wallet hates me a the start of the season 140 for a oe polaris belt sucks Before I continue, if I don't keep this sled for the whole season, I promise to never sign on to Snowmobile Fanatics again. BRP...... 2001 xc 800 sp | 1998 XCR 600 | 1999 Ski-doo formula 670 - SLP air horn | - 192 woodys | - 30 miles - 5 inch riser | - 9000miles | - 2 motors - 192 woodys | - Tripple Pipes | - and alot of head aches - 6400miles | -Gas and Go | - 10000km - CLUTCHED - 128 polaris track Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 5:36 PM Post #4
	James007 Disturbing the peace since 1991. 2090 Posts Group: Members Member Since: January 12th 2007 Location: kirkland lake, ontario, Canada Current Sled: 2009 MXZ X 600Etec 2008-2009 Miles: 1100
	So basically i should just not beat around the bush and buy good belt 2009 MXZ X 600 ETEC www.youtube.com/sjames117 Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 5:44 PM Post #5
	rougepolaris s#^t happens 498 Posts Group: Members Member Since: September 2nd 2008 Location: williamstown, new york, USA Current Sled: polaris xcsp 600 2008-2009 Miles: 814
	^^^^ ya pretty much empty a bag of skittles in the toilet and flush it;s like watching a 5 second nascar race Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 5:48 PM Post #6
	killerbee52j The X package 1753 Posts Group: Members Member Since: March 12th 2007 Location: Hamburg, ny, USA Current Sled: 08 mxzx 600 sdi 2008-2009 Miles: 1800
	Go for the $80 ski-doo belt.Ive had good luck with them.Over 2000 miles on one sled and i got over 1000 miles on my sled.I blew it last year on the lake. "ride it like you stole it" "the 6 pack is under the keg" Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 5:50 PM  [ Modified December 28th 2008 at 5:53 PM ] Post #7
	proxJ Senior Member 4604 Posts Group: Members Member Since: November 7th 2005 Location: West.St.Paul, Manitoba, Canada Current Sled: 04 rev 600 x,06 mxzx 440 2008-2009 Miles: 0
	Dont put those ****in pos aftermarket belts on that doo, will just go KAAAABOOOOM just like there motors ha ha. These will help a bit. QRS Shim Package PRICE $45.00 USD QRS Shim Package In testing, this kit has shown to reduce belt temps up to 70*f, increase belt life and provide more consistent RPM's. Between my personal sled and the 3 different test sleds have shown zero belt wear with a total test mileage of 3450. Test sleds where a 08 TNT, 08 MXZ-X800R, 08 Summit 800R run @ 1000 – 10000 ft elevations, aggressive trail riding as well as mile after mile of WFO powder riding. The QRS shim package consists of 5 bearing shims and 3 spacers to support the inner race of the upper chain case bearing. With this package you will be able to shim the secondary 2-5mm and have the proper spacers to support the upper chain case bearing and prevent any oil loss through the upper seal as well as bearing failure due to unnecessary side load. Simple 20 minute install. Price will be $45.00 shipped in the lower 48 and $52.00 shipped to our Canadian neighbors Pay will be accepted to Dynamicrecovery@comcast.net Contact Email: Dynamicrecovery@comcast.net XP Clutch Tower Brace PRICE $100.00 USD XP Clutch Tower Brace -stabalizes secondary and helps keep clutches aligned -will also help avoid any catastrophic failure of the driven pulley support -simple installation with no drilling or permanant modifications to the sled -will fit all XP chassis $100 Canadian plus shipping Youl find the adds on this page. http://www.dootalk.com/dtproducts.php revegade Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 6:25 PM  [ Modified December 28th 2008 at 6:25 PM ] Post #8
	500EFISKS Willing to learn how about you? 102 Posts Group: Members Member Since: July 3rd 2005 Location: Lumsden, Saskatchewan, Canada
	An Ultimax XS belt will last. Incredible technology. About $120 Can. but if your clutches are aligned properly you will not be replacing this belt for many miles. This if proven testimony. Rating: 0 Quick Edit Full Edit

	December 28th 2008 at 11:57 PM Post #9
	James007 Disturbing the peace since 1991. 2090 Posts Group: Members Member Since: January 12th 2007 Location: kirkland lake, ontario, Canada Current Sled: 2009 MXZ X 600Etec 2008-2009 Miles: 1100
	Im going to look into that thanks proxJ I was also looking at the ultimax 3 belt. i seen it on snowmobilerTV today. 2009 MXZ X 600 ETEC www.youtube.com/sjames117 Rating: 0 Quick Edit Full Edit

	December 29th 2008 at 12:19 AM Post #10
	proxJ Senior Member 4604 Posts Group: Members Member Since: November 7th 2005 Location: West.St.Paul, Manitoba, Canada Current Sled: 04 rev 600 x,06 mxzx 440 2008-2009 Miles: 0
	Stick with doo, belive me, anything else will go booom. revegade Rating: 0 Quick Edit Full Edit